Upload files to "PrusaSlicer"
This commit is contained in:
parent
dcb489c653
commit
d2a6096d65
419
PrusaSlicer/Ender_3_Klipperized-PrusaSlicer_config_bundle.ini
Normal file
419
PrusaSlicer/Ender_3_Klipperized-PrusaSlicer_config_bundle.ini
Normal file
@ -0,0 +1,419 @@
|
||||
# generated by PrusaSlicer 2.7.4 on 2024-08-06 at 18:50:35 UTC
|
||||
|
||||
[print:Ender 3 Pro - 0.20 mm NORMAL SPEED (0.4 mm nozzle)]
|
||||
arc_fitting = disabled
|
||||
avoid_crossing_curled_overhangs = 0
|
||||
avoid_crossing_perimeters = 0
|
||||
avoid_crossing_perimeters_max_detour = 0
|
||||
bottom_fill_pattern = monotonic
|
||||
bottom_solid_layers = 4
|
||||
bottom_solid_min_thickness = 0
|
||||
bridge_acceleration = 250
|
||||
bridge_angle = 0
|
||||
bridge_flow_ratio = 0.95
|
||||
bridge_speed = 25
|
||||
brim_separation = 0
|
||||
brim_type = outer_only
|
||||
brim_width = 0
|
||||
compatible_printers =
|
||||
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
|
||||
complete_objects = 0
|
||||
default_acceleration = 500
|
||||
dont_support_bridges = 1
|
||||
draft_shield = disabled
|
||||
elefant_foot_compensation = 0.1
|
||||
enable_dynamic_overhang_speeds = 1
|
||||
external_perimeter_acceleration = 0
|
||||
external_perimeter_extrusion_width = 0.42
|
||||
external_perimeter_speed = 20
|
||||
external_perimeters_first = 0
|
||||
extra_perimeters = 0
|
||||
extra_perimeters_on_overhangs = 0
|
||||
extruder_clearance_height = 25
|
||||
extruder_clearance_radius = 55
|
||||
extrusion_width = 0.44
|
||||
fill_angle = 45
|
||||
fill_density = 15%
|
||||
fill_pattern = gyroid
|
||||
first_layer_acceleration = 0
|
||||
first_layer_acceleration_over_raft = 0
|
||||
first_layer_extrusion_width = 0.42
|
||||
first_layer_height = 0.2
|
||||
first_layer_speed = 18
|
||||
first_layer_speed_over_raft = 30
|
||||
fuzzy_skin = none
|
||||
fuzzy_skin_point_dist = 0.8
|
||||
fuzzy_skin_thickness = 0.3
|
||||
gap_fill_enabled = 1
|
||||
gap_fill_speed = 30
|
||||
gcode_comments = 0
|
||||
gcode_label_objects = octoprint
|
||||
gcode_resolution = 0.0125
|
||||
gcode_substitutions =
|
||||
infill_acceleration = 0
|
||||
infill_anchor = 600%
|
||||
infill_anchor_max = 50
|
||||
infill_every_layers = 1
|
||||
infill_extruder = 1
|
||||
infill_extrusion_width = 0.44
|
||||
infill_first = 0
|
||||
infill_overlap = 23%
|
||||
infill_speed = 30
|
||||
inherits = 0.20 mm NORMAL SPEED (0.4 mm nozzle) @CREALITY
|
||||
interface_shells = 0
|
||||
ironing = 0
|
||||
ironing_flowrate = 10%
|
||||
ironing_spacing = 0.1
|
||||
ironing_speed = 20
|
||||
ironing_type = top
|
||||
layer_height = 0.2
|
||||
max_print_speed = 100
|
||||
max_volumetric_extrusion_rate_slope_negative = 0
|
||||
max_volumetric_extrusion_rate_slope_positive = 0
|
||||
max_volumetric_speed = 0
|
||||
min_bead_width = 85%
|
||||
min_feature_size = 25%
|
||||
min_skirt_length = 4
|
||||
mmu_segmented_region_interlocking_depth = 0
|
||||
mmu_segmented_region_max_width = 0
|
||||
notes =
|
||||
only_retract_when_crossing_perimeters = 0
|
||||
ooze_prevention = 0
|
||||
output_filename_format = {input_filename_base}_{print_time}_{digits(layer_height,1,2)}mm_{temperature[0]}C_{filament_type[0]}_{printer_model}.gcode
|
||||
overhang_speed_0 = 15
|
||||
overhang_speed_1 = 15
|
||||
overhang_speed_2 = 20
|
||||
overhang_speed_3 = 25
|
||||
overhangs = 0
|
||||
perimeter_acceleration = 0
|
||||
perimeter_extruder = 1
|
||||
perimeter_extrusion_width = 0.44
|
||||
perimeter_generator = arachne
|
||||
perimeter_speed = 30
|
||||
perimeters = 3
|
||||
post_process =
|
||||
print_settings_id =
|
||||
raft_contact_distance = 0.1
|
||||
raft_expansion = 1.5
|
||||
raft_first_layer_density = 90%
|
||||
raft_first_layer_expansion = 3
|
||||
raft_layers = 0
|
||||
resolution = 0
|
||||
seam_position = nearest
|
||||
single_extruder_multi_material_priming = 0
|
||||
skirt_distance = 3
|
||||
skirt_height = 1
|
||||
skirts = 2
|
||||
slice_closing_radius = 0.049
|
||||
slicing_mode = regular
|
||||
small_perimeter_speed = 20
|
||||
solid_infill_acceleration = 0
|
||||
solid_infill_below_area = 0
|
||||
solid_infill_every_layers = 0
|
||||
solid_infill_extruder = 1
|
||||
solid_infill_extrusion_width = 0.44
|
||||
solid_infill_speed = 30
|
||||
spiral_vase = 0
|
||||
staggered_inner_seams = 0
|
||||
standby_temperature_delta = -5
|
||||
support_material = 0
|
||||
support_material_angle = 0
|
||||
support_material_auto = 1
|
||||
support_material_bottom_contact_distance = 0
|
||||
support_material_bottom_interface_layers = -1
|
||||
support_material_buildplate_only = 0
|
||||
support_material_closing_radius = 2
|
||||
support_material_contact_distance = 0.15
|
||||
support_material_enforce_layers = 0
|
||||
support_material_extruder = 0
|
||||
support_material_extrusion_width = 0.36
|
||||
support_material_interface_contact_loops = 0
|
||||
support_material_interface_extruder = 0
|
||||
support_material_interface_layers = 2
|
||||
support_material_interface_pattern = rectilinear
|
||||
support_material_interface_spacing = 0.2
|
||||
support_material_interface_speed = 100%
|
||||
support_material_pattern = rectilinear
|
||||
support_material_spacing = 1
|
||||
support_material_speed = 30
|
||||
support_material_style = grid
|
||||
support_material_synchronize_layers = 0
|
||||
support_material_threshold = 40
|
||||
support_material_with_sheath = 0
|
||||
support_material_xy_spacing = 60%
|
||||
support_tree_angle = 40
|
||||
support_tree_angle_slow = 25
|
||||
support_tree_branch_diameter = 2
|
||||
support_tree_branch_diameter_angle = 5
|
||||
support_tree_branch_diameter_double_wall = 3
|
||||
support_tree_branch_distance = 1
|
||||
support_tree_tip_diameter = 0.8
|
||||
support_tree_top_rate = 15%
|
||||
thick_bridges = 1
|
||||
thin_walls = 0
|
||||
top_fill_pattern = monotonic
|
||||
top_infill_extrusion_width = 0.4
|
||||
top_solid_infill_acceleration = 0
|
||||
top_solid_infill_speed = 20
|
||||
top_solid_layers = 5
|
||||
top_solid_min_thickness = 0
|
||||
travel_acceleration = 0
|
||||
travel_speed = 150
|
||||
travel_speed_z = 0
|
||||
wall_distribution_count = 1
|
||||
wall_transition_angle = 10
|
||||
wall_transition_filter_deviation = 25%
|
||||
wall_transition_length = 100%
|
||||
wipe_tower = 0
|
||||
wipe_tower_acceleration = 0
|
||||
wipe_tower_bridging = 10
|
||||
wipe_tower_brim_width = 2
|
||||
wipe_tower_cone_angle = 0
|
||||
wipe_tower_extra_flow = 100%
|
||||
wipe_tower_extra_spacing = 100%
|
||||
wipe_tower_extruder = 0
|
||||
wipe_tower_no_sparse_layers = 0
|
||||
wipe_tower_rotation_angle = 0
|
||||
wipe_tower_width = 60
|
||||
wipe_tower_x = 170
|
||||
wipe_tower_y = 140
|
||||
xy_size_compensation = 0
|
||||
|
||||
[filament:steeb's PETG]
|
||||
bed_temperature = 90
|
||||
bridge_fan_speed = 50
|
||||
compatible_printers =
|
||||
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 1
|
||||
disable_fan_first_layers = 3
|
||||
enable_dynamic_fan_speeds = 0
|
||||
end_filament_gcode = "; Filament-specific end gcode"
|
||||
extrusion_multiplier = 1
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 20
|
||||
filament_colour = #FFFFFF
|
||||
filament_cooling_final_speed = 2
|
||||
filament_cooling_initial_speed = 3
|
||||
filament_cooling_moves = 1
|
||||
filament_cost = 27.82
|
||||
filament_density = 1.27
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 14
|
||||
filament_loading_speed_start = 19
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 0
|
||||
filament_multitool_ramming = 0
|
||||
filament_multitool_ramming_flow = 10
|
||||
filament_multitool_ramming_volume = 10
|
||||
filament_notes = ""
|
||||
filament_purge_multiplier = 100%
|
||||
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = 2
|
||||
filament_retract_length_toolchange = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_restart_extra_toolchange = nil
|
||||
filament_retract_speed = 40
|
||||
filament_settings_id = ""
|
||||
filament_soluble = 0
|
||||
filament_spool_weight = 0
|
||||
filament_stamping_distance = 0
|
||||
filament_stamping_loading_speed = 20
|
||||
filament_toolchange_delay = 0
|
||||
filament_travel_lift_before_obstacle = nil
|
||||
filament_travel_max_lift = nil
|
||||
filament_travel_ramping_lift = nil
|
||||
filament_travel_slope = nil
|
||||
filament_type = PETG
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 20
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = Generic
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 85
|
||||
first_layer_temperature = 230
|
||||
full_fan_speed_layer = 5
|
||||
idle_temperature = nil
|
||||
inherits = Generic PETG @Template
|
||||
max_fan_speed = 50
|
||||
min_fan_speed = 30
|
||||
min_print_speed = 10
|
||||
overhang_fan_speed_0 = 0
|
||||
overhang_fan_speed_1 = 0
|
||||
overhang_fan_speed_2 = 0
|
||||
overhang_fan_speed_3 = 0
|
||||
slowdown_below_layer_time = 10
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 240
|
||||
|
||||
[filament:steeb's PLA]
|
||||
bed_temperature = 60
|
||||
bridge_fan_speed = 100
|
||||
compatible_printers =
|
||||
compatible_printers_condition =
|
||||
compatible_prints =
|
||||
compatible_prints_condition =
|
||||
cooling = 0
|
||||
disable_fan_first_layers = 3
|
||||
enable_dynamic_fan_speeds = 0
|
||||
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
||||
extrusion_multiplier = 1
|
||||
fan_always_on = 1
|
||||
fan_below_layer_time = 60
|
||||
filament_colour = #0E5FED
|
||||
filament_cooling_final_speed = 3.4
|
||||
filament_cooling_initial_speed = 2.2
|
||||
filament_cooling_moves = 0
|
||||
filament_cost = 19.35
|
||||
filament_density = 1.23
|
||||
filament_deretract_speed = nil
|
||||
filament_diameter = 1.75
|
||||
filament_load_time = 0
|
||||
filament_loading_speed = 28
|
||||
filament_loading_speed_start = 3
|
||||
filament_max_volumetric_speed = 0
|
||||
filament_minimal_purge_on_wipe_tower = 15
|
||||
filament_multitool_ramming = 0
|
||||
filament_multitool_ramming_flow = 10
|
||||
filament_multitool_ramming_volume = 10
|
||||
filament_notes = ";Full spool weight: 1280g"
|
||||
filament_purge_multiplier = 100%
|
||||
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
||||
filament_retract_before_travel = nil
|
||||
filament_retract_before_wipe = nil
|
||||
filament_retract_layer_change = nil
|
||||
filament_retract_length = nil
|
||||
filament_retract_length_toolchange = nil
|
||||
filament_retract_lift = nil
|
||||
filament_retract_lift_above = nil
|
||||
filament_retract_lift_below = nil
|
||||
filament_retract_restart_extra = nil
|
||||
filament_retract_restart_extra_toolchange = nil
|
||||
filament_retract_speed = nil
|
||||
filament_settings_id = "ABS - KVP"
|
||||
filament_soluble = 0
|
||||
filament_spool_weight = 1000
|
||||
filament_stamping_distance = 0
|
||||
filament_stamping_loading_speed = 20
|
||||
filament_toolchange_delay = 0
|
||||
filament_travel_lift_before_obstacle = nil
|
||||
filament_travel_max_lift = nil
|
||||
filament_travel_ramping_lift = nil
|
||||
filament_travel_slope = nil
|
||||
filament_type = PLA
|
||||
filament_unload_time = 0
|
||||
filament_unloading_speed = 90
|
||||
filament_unloading_speed_start = 100
|
||||
filament_vendor = (Unknown)
|
||||
filament_wipe = nil
|
||||
first_layer_bed_temperature = 65
|
||||
first_layer_temperature = 210
|
||||
full_fan_speed_layer = 0
|
||||
idle_temperature = nil
|
||||
inherits =
|
||||
max_fan_speed = 100
|
||||
min_fan_speed = 100
|
||||
min_print_speed = 10
|
||||
overhang_fan_speed_0 = 0
|
||||
overhang_fan_speed_1 = 0
|
||||
overhang_fan_speed_2 = 0
|
||||
overhang_fan_speed_3 = 0
|
||||
slowdown_below_layer_time = 5
|
||||
start_filament_gcode = "; Filament gcode\n"
|
||||
temperature = 200
|
||||
|
||||
[printer:Klipperized Ender-3 Pro (0.4 mm nozzle)]
|
||||
autoemit_temperature_commands = 1
|
||||
bed_custom_model =
|
||||
bed_custom_texture =
|
||||
bed_shape = 3x3,228x3,228x228,3x228
|
||||
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0\n;{layer_z}\n\n
|
||||
between_objects_gcode =
|
||||
binary_gcode = 0
|
||||
color_change_gcode = M600
|
||||
cooling_tube_length = 5
|
||||
cooling_tube_retraction = 91.5
|
||||
default_filament_profile = "Generic PLA @CREALITY"
|
||||
default_print_profile = "0.16 mm OPTIMAL (0.4 mm nozzle) @CREALITY"
|
||||
deretract_speed = 40
|
||||
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
|
||||
extra_loading_move = -2
|
||||
extruder_colour = #FCE94F
|
||||
extruder_offset = 0x0
|
||||
gcode_flavor = klipper
|
||||
high_current_on_filament_swap = 0
|
||||
host_type = prusalink
|
||||
inherits = Creality Ender-3 Pro (0.4 mm nozzle)
|
||||
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
|
||||
machine_limits_usage = time_estimate_only
|
||||
machine_max_acceleration_e = 5000
|
||||
machine_max_acceleration_extruding = 500
|
||||
machine_max_acceleration_retracting = 1000
|
||||
machine_max_acceleration_travel = 500
|
||||
machine_max_acceleration_x = 500
|
||||
machine_max_acceleration_y = 500
|
||||
machine_max_acceleration_z = 100
|
||||
machine_max_feedrate_e = 60
|
||||
machine_max_feedrate_x = 500
|
||||
machine_max_feedrate_y = 500
|
||||
machine_max_feedrate_z = 10
|
||||
machine_max_jerk_e = 5
|
||||
machine_max_jerk_x = 8
|
||||
machine_max_jerk_y = 8
|
||||
machine_max_jerk_z = 0.4
|
||||
machine_min_extruding_rate = 0
|
||||
machine_min_travel_rate = 0
|
||||
max_layer_height = 0.32
|
||||
max_print_height = 250
|
||||
min_layer_height = 0.06
|
||||
multimaterial_purging = 140
|
||||
nozzle_diameter = 0.4
|
||||
parking_pos_retraction = 92
|
||||
pause_print_gcode = M25 ; pause print
|
||||
print_host =
|
||||
printer_model = ENDER3PRO
|
||||
printer_settings_id =
|
||||
printer_technology = FFF
|
||||
printer_variant = 0.4
|
||||
printer_vendor =
|
||||
printhost_apikey =
|
||||
printhost_cafile =
|
||||
remaining_times = 0
|
||||
retract_before_travel = 2
|
||||
retract_before_wipe = 70%
|
||||
retract_layer_change = 1
|
||||
retract_length = 5
|
||||
retract_length_toolchange = 1
|
||||
retract_lift = 0
|
||||
retract_lift_above = 0.2
|
||||
retract_lift_below = 0
|
||||
retract_restart_extra = 0
|
||||
retract_restart_extra_toolchange = 0
|
||||
retract_speed = 60
|
||||
silent_mode = 0
|
||||
single_extruder_multi_material = 0
|
||||
start_gcode = G90 ; use absolute coordinates\n\nM83 ; extruder relative mode\nM104 S{is_nil(idle_temperature[0]) ? 150 : idle_temperature[0]} ; set temporary nozzle temp to prevent oozing during homing\nM140 S{first_layer_bed_temperature[0]} ; set final bed temp\nG28 ; home all axis\nM190S{first_layer_bed_temperature[0]} ; wait for bed temp to calibrate bed mesh\nG4 S30 ; allow partial nozzle warmup\n\n\nM117\n\nBED_MESH_CALIBRATE ; do KAMP stuff\n\nG1 Z15 F240\nG1 X2.0 Y10 F3000\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize\n\n\nM104 S{first_layer_temperature[0]} ; set final nozzle temp\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize\nM109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\n\nG92 E0\n\n\nSTART_PRINT\n\nLINE_PURGE
|
||||
template_custom_gcode =
|
||||
thumbnails =
|
||||
thumbnails_format = PNG
|
||||
toolchange_gcode =
|
||||
travel_lift_before_obstacle = 0
|
||||
travel_max_lift = 0
|
||||
travel_ramping_lift = 0
|
||||
travel_slope = 0
|
||||
use_firmware_retraction = 0
|
||||
use_relative_e_distances = 1
|
||||
use_volumetric_e = 0
|
||||
variable_layer_height = 1
|
||||
wipe = 1
|
||||
z_offset = 0
|
||||
|
||||
Loading…
Reference in New Issue
Block a user